1967 Camaro Shifter

SHIFTWORKS® is now offering a new replica of the 67 Camaro shifter. Our shifter has some design changes that make is easier to use with different transmissions. Currently the shifter will work with GM 3 and 4 speed automatics. The Powerglide version is now available.

Original and Shiftworks version - larger view

Shifter for PowerGlide:

Complete with rod linkage, optional off sets and Neutral Safety/Backup light switch. Uses pre-existing PG range select lever at transmission. Shiftworks will be offering parts to connect to any PowerGlide December 2011.

SW280-PGT………………..$325.00

Shifter for all Turbohydramatics:
TH350, TH400, TH200-4R, TH700-R4, 4L60, 4L80

Complete with linkage, optional off sets,
and Neutral Safety/Backup light switch.

#SW280-RCT . . . .$350.00

DO You have a : 4L60E, 4L70E, or 4L80E with the neutral safety switch on the outside?

Then you will need our 4LE Fix it kit. This allows you to connect the linkage and not have any conflicts with the switch.

4LE Rod Linkage fix-it . . . . . $18.50

Shifter Conversion

Powerglide & TH Shifter
Conversion Kits

Use your factory-installed automatic floor shifter with a newer 3-speed (TH350 or TH400) or 4-speed overdrive (TH700-R4, TH200-4R or 4L60) transmission. This kit retains the rod linkage. The conversion includes a new laser cut and hardened detent for proper stops and gear selection, a new matching transmission shift lever, all necessary hardware, and instructions.

 

1967 Camaro   3 Speed Installation TH350 & TH400 #S105A . . . .$57.75 Note:  Check shifter clearance here
1967 Camaro   4 Speed Overdrive Kit TH200-4R, TH700-R4 & 4L60 #S105B  . . . .$57.75 Note:  Check shifter clearance here
Neutral Safety/Backup Switch Designed for the TH and OD conversion. #S519. . . . $38.50 See switch installed and working
Neutral Safety Switch and Back-up Light actuator #S635. . . $15.25
Swivel Kit Install a new swivel and grommets to help eliminate the loose feel and poor adjustment caused by worn linkage. #SW404 ....... $9.50

1967 Rod Linkage with Swivel Kit

#SW429 ....... $41.00 

5/16 inch Rod linkage using right hand and left hand ball joints on each end. 15 inch rod can be shortened and will accommodate lengths from 16.5 inches to 12.5 inches. Use of L and R hand threads makes adjustment simple by spinning rod to lengthen or shorten when installed. Jam nuts included to tighten linkage as well.

#S415 ....... $28.50





.



1967 Camaro Shifter Parts

Shifter Release Button #6724 . . .$12.50
Release Spring #S501. . . $4.50 This spring must be used under the shifter release button for proper operation of shifter. (Often Missing)
Flexi-Rod Shift Actuator This is a new Flexi-Rod shift actuator that will replace the original GM stamped spring steel actuator found in the 67 Camaro/Firebird, and 68-72 Nova automatic transmission console shifters. The original spring steel actuators are prone to break (after 35+ years use), rendering the shifter useless. Also, we have seen many vintage shifters where the tang is worn or destroyed with use, also rendering the shifter useless. The barbed top end that mates to the black plastic button, and the bottom tang are both hardened for long use. #S636 ....... $54.50
Plastic (Delrin) Bushings #S504. . . $12.75
Neutral Safety/Backup Switch Designed for the TH and OD conversion. #S519. . . . $38.50   See switch installed and working
Neutral Safety Switch and Back-up Light actuator #S635. . . $15.25
Bottom Spring #SW442 . . . . $4.50
Use SW442 if your handle has a screw in Bottom UseSW443 if your handle has a cotter pin bottom
Washers #S441. . . $6.50 Theses two 5/8" washers are often missing or rusted away. Without them your shifter will be sloppy. A nice fix.
exploded view of shifter assembly

1967 Camaro   Powerglide Transmission Parts Select Lever #SW419 . . . . .$42.00	* Note- before ordering check your transmission here.
Swivel Kit #SW404 ....... $9.50

.

information@shiftworks.com
  Copyright © 1997-

This page designed and maintained by 

  Please report any problems
to Word Works